Team Associated - RC10B6.3 Team Kit - 1/10 2WD Electric Buggy
Team Associated - RC10B6.3 Team Kit - 1/10 2WD Electric Buggy
Team Associated - RC10B6.3 Team Kit - 1/10 2WD Electric Buggy
Team Associated - RC10B6.3 Team Kit - 1/10 2WD Electric Buggy
Team Associated - RC10B6.3 Team Kit - 1/10 2WD Electric Buggy
Team Associated - RC10B6.3 Team Kit - 1/10 2WD Electric Buggy
Team Associated

Team Associated - RC10B6.3 Team Kit - 1/10 2WD Electric Buggy

Regular price $329.99 Sale price $529.99 Unit price per
Shipping calculated at checkout.

This vehicle comes as a kit and must be fully assembled by the user. Electronics and motor are required.

New Features

  • New wide pivot rear aluminum arm mounts for use with 73mm arms and 69mm CVA bones to give more predictable rear traction and an easy-to-drive rear-end feel
  • New servo mounting system with aluminum chassis mounts and molded brace is much easier to assemble and has an integrated transponder mount
  • New molded front and rear tower covers protect the edges of the carbon fiber from damage, and keeps from damaging the track surface
  • Octalock spur gear and 11mm Octalock LCF pads using the heavier RC10B74.1 slipper spring for maximum consistency and higher torque capacity
  • Tie-rod battery brace parts and hardware included in kit for tuning additional chassis flex
  • Molded wire clips included for motor and ESC wires to keep your wiring organized

Updated Features

  • Updated carbon fiber front and rear shock towers with fine hole spacing adjustment
  • +3mm extended chassis length for additional stability and reduced weight transfer in high-traction conditions
  • Updated chassis and side rails for use with new direct-to-chassis servo mount giving a more direct steering feel and predictable chassis flex going into and out of corners
  • Updated top plate that keys to a new steering bellcrank brace for increased durability
  • Updated rear wing mounts for more durability and less bending
  • Set screw and flanged nut rear bottom shock mounting hardware for quick and easy shock removal
  • +1 carbon fiber steering arms
  • Black steel M4 low profile (LP) serrated wheel nuts

Legacy Features

  • 3-gear Laydown Stealth(R) transmission assembly for optimal mass balance on high- grip clay track surfaces
  • Fluid-filled gear differential included to withstand high load cornering
  • Front and rear anti-roll bars included to provide less chassis roll on high-grip surfaces
  • V2 12mm Big Bore threaded aluminum shocks with X-rings for low friction assembly
  • Machined shock pistons for more precise fit and smoother operation
  • V2 12mm shock springs for lower achievable ride height and nimbler feel
  • Aluminum rear ballstud mount with three link positions for maximum adjustability and added strength
  • Factory Team ball bearing set with 24 precision ball bearings, now oiled instead of greased for more efficient drivetrain
  • Easy-access differential with 0, 1, 2, and 3mm height adjustment inserts included. (RC10B6.3 comes with a gear differential). Height adjustment inserts allow driveshaft alignment through all ride height and axle height configurations
  • Rear hub assembly with aluminum vertical ball stud camber link mount and axle height inserts for precise roll center adjustment
  • Front wing mount and front wing included to increased downforce and front grip
  • Integrated 30mm fan mount (fan not included) to prevent motor fade due to overheating
  • 69mm CVA bones for reduced bone plunge and minimized friction at drive pin
  • The symmetric rear arms with improved geometry and stiffness can be flipped to allow a "split" for rear shock mounting position. Arms are available in 73mm and 75mm lengths (73mm included)
  • Outer rear hinge pin is captured with bolt head and lock nut for increased durability
  • Steel electronics and steel under-servo plates included for improved mass balance and lower overall center of mass
  • 5mm aluminum clamping wheel hexes
  • Lightweight aluminum one-piece top shaft and gear
  • Body designed with lower center of mass improves handling on high-grip surfaces (clear body and wing included)

Vehicle Specifications

  • Power Source: Electric
  • Terrain: Off-Road
  • Body Style: Buggy
  • Scale Size: 1:10 Scale
  • Assembly Level: Kit*
  • Length: 390mm (15.35in)
  • Width: varies
  • Wheelbase: varies
  • Weight: 821g (1.81lbs)
  • Drive: 2WD
  • * This vehicle comes as a kit and must be fully assembled by the user. Electronics and/or an engine/motor may be required.

Required to Complete

  • 1:10 scale electric motor and electronic speed control
  • 7.4V, 7.6V 2S LiPo with "shorty" battery dimensions (Reedy batteries #27363, #27364, #27365, #27366)
  • Battery charger (#27200)
  • 2-channel surface transmitter
  • 2-channel receiver
  • Steering servo (#27100, #27101, #27109, #27118, #27119)
  • Lexan(TM)-specific spray paint for body
  • 1:10 scale off-road wheels and tires
  • Pinion gear
  • Other helpful items: Silicone shock fluid, Silicone diff fluid, FT body scissors, FT body reamer, FT hex/nut driver set , CA tire adhesive, Hobby knife, Needle nose pliers, Wire cutters, Soldering iron, Calipers or precision ruler